Step and Repeat Size: 8×8 vs. 10×8 and Easy Logo Spacing
The right step and repeat size depends on how many people pose at once and how much wall you have. As a rough start, we would use an 8-foot-wide backdrop for one to three people and about 10 feet wide for groups of four to six. One event photographer warns that an 8 x 8 is too small for large groups, because people end up past the edges [4]. How people pose, how close they stand, and where the camera sits all change what fits.
Then size and space the logos so a full one shows up behind each person.
Below is how to pick the size, measure your room, and lay out logos for the camera. Treat the numbers as starting points, not standards.
Table of Contents
What a step and repeat is
A step and repeat is a backdrop printed with a logo, or a few sponsor logos, repeated in a pattern across the whole surface. Guests pose in front of it, so the brand shows up in their photos and in anything they share [4].

You see them at galas, press events, grand openings, parties and trade shows. Our Step and Repeat Backdrop is built for those events and can double as a trade show backdrop [1].
Step and repeat size by group
Here is how we would match step and repeat size to group size. These are our own rough starting points, not standards. Sizes below are width × height. Some printers write them the other way around.
| Who poses at once | Width to start with | Notes |
|---|---|---|
| 1 person or a couple | 8 feet | Plenty of room |
| Up to about 3 people | 8 feet | Check that nobody stands past the edge |
| Groups of 4 to 6 | 10 feet | Room to stand side by side |
| Large groups and press lines | Wider than 10 feet | Ask us first, as our listed sizes stop at 10 feet [1] |
Our backdrop is 8 feet high. It comes 8, 9 or 10 feet wide: 8 × 8, 9 × 8 and 10 × 8 [1]. You can also pick any custom size from 6 × 4 up to 10 × 8 feet, width first [1].
So for step and repeat size, the 8 × 8 is our starting point for one to three people. The 10 × 8 suits groups of four to six. Bigger banners cost more, so people often order small. But a group that spills past the edges loses the clean look you paid for [4]. Estimate your largest group first [4].
Height: the other half of step and repeat size
Height matters for photos too. Need extra space above tall guests, or plan to shoot from higher up? Tell us before you order, since our listed sizes are 8 feet high [1].
Also check the ceiling. The backdrop plus its stand must fit under yours, so measure the real room and do not assume.
Measure the room before you pick a step and repeat size
The backdrop has to fit the space without crowding it. Measure the spot where it will stand, both width and height [4].
Remember that the stand adds to the floor space you need. The frame and its feet take up room beyond the printed graphic. Leave clear walkways around it too, so it does not block paths. Have sandbags or weights on hand as well, so the backdrop cannot tip or shift during the event [4].
Logo size and spacing
Three ideas do most of the work: repeat the logo, keep the gaps even, and offset each row.
Use a staggered grid. We suggest shifting each row sideways by half the distance from one logo to the next, like bricks in a wall. That way a cropped photo is more likely to catch a full logo.
Size the logos so they read in a photo. One event photographer suggests logos about 12 inches high and 12 to 24 inches wide, with enough space between them that the wall does not look crowded [4].
Here is how that works out with 12-inch logos and 6-inch gaps, which is our own arithmetic and not a rule:
| Backdrop width | Full logos in an unshifted row | Left over for outer margins |
|---|---|---|
| 8 feet (96 inches) | 5 logos, 4 gaps | 12 inches |
| 10 feet (120 inches) | 6 logos, 5 gaps | 18 inches |
Staggered rows may fit fewer full logos, or end with a logo cut off at the edge.
Spread sponsor logos evenly. If you have several sponsors, mix them through the pattern so no brand clusters in one corner. Keep their sizes balanced unless you have agreed that one sponsor gets more space.
Mixing several sponsor logos
Sponsor logos come in different shapes, which can make a wall look messy. We suggest sizing wide logos by their width. Then measure the gap between rows from the tallest logo in the set, so mixed logos still sit on one clean line.
When you send your files, include every logo in high resolution or as vector art [4]. Say whether all logos should be the same size, or whether some brands get more space. That decision changes the whole pattern, so settle it with your sponsors before design starts.
Keep logos out of the pole pockets
The graphic slides onto our frame through 3-inch pole pockets at the top and bottom [1]. A pole pocket is a sewn sleeve that the frame bar slides through. Keep important logos out of the pockets and any finishing areas shown on the product template.

Think about what the camera will crop as well. One event photographer advises against a large title across the upper part of the banner, because a close-up can cut it off in strange ways [4]. We also suggest keeping the lowest part of the wall free of logos, because guests and the stand base cover that strip. Where a product template shows different margins, follow the template.
Fabric for the camera
Think about the camera flash too. A non-reflective surface helps prevent glare from camera flashes and room lights [4]. We print the backdrop on a wrinkle-free 9 oz low-sheen fabric [1]. Low-sheen fabric can help reduce flash reflections, but the lighting angle still matters.
A taut graphic looks better in photos, and setting it up early gives wrinkles time to stretch out [4]. Correct frame adjustment and a properly fitted graphic help reduce slack. The frame uses thick 1.625-inch slide-out poles and weighted feet [1]. Rooms can be dim as well, so plan your lighting if you do not have a professional photographer [4].
Build the file
Make your logo pattern as vector art if you can. That is a logo file drawn with lines and shapes, such as an EPS or SVG, so it stays sharp when printed large [4]. Use design software that lets you duplicate, align and space logos accurately.
For our backdrop, send a JPG or single-page PDF in CMYK at the size you order [1]. Follow the supplied template dimensions when they differ from the ordered display size [3]. Use at least 150 dpi, with no crop marks or bleed [1]. Not sure how to lay out the pattern? Our design team can build it and send you a mockup first [1].
Limits of these numbers
The step and repeat size and spacing figures above come from one photographer’s advice and our own starting points, not an industry standard. Your camera, lens, lighting and how far the photographer stands all change what fits in the frame. If you can, set up the backdrop before the event and take a few test photos.
How we can help
The Step and Repeat Backdrop comes with a fabric graphic, slide-out frame, weighted feet and a carry bag [1]. Already have a frame? Order a new graphic for your next event and reuse it [1], or buy the frame on its own.
For more backdrops and banners, see our custom banners. Not sure which step and repeat size fits your room? Ask us before you order.
Frequently asked questions
What step and repeat size should I start with?
We would start with 8 × 8 feet for one to three people at a time [1]. Go wider if bigger groups will pose together, so nobody stands past the edge [4].
How many logos fit on an 8-foot step and repeat?
With 12-inch logos and 6-inch gaps, about five full logos fit across each row. How many rows depends on your logo’s height and the gaps you choose.
Can I reuse my step and repeat?
Yes. You can keep the frame and order a new printed graphic for the next event [1].
How far ahead should I order a step and repeat?
Mention your event date when you order, and we will check whether your deadline can be met [2]. Larger items can take longer to produce [2]. Order early, and leave time to set up the backdrop in the real room before the event.
Should I put the event name on the backdrop?
You can, but keep it small and away from the top. A large title across the upper part can get cut off in close-ups, and one event photographer prefers adding it to the photos afterward [4]. Spell the text exactly as you want it printed.
Sources
- Step and Repeat Backdrop, 15X Prints: sizes, custom range, 3-inch pole pockets, low-sheen 9 oz fabric, 1.625-inch poles, weighted feet, carry bag, graphic-only option, file specs, design help
- Shipping Policy, 15X Prints: tell us your event date when you order; larger items may take longer to produce
- Help Center, 15X Prints: when a template is used, the file must match the template size
- Helpful Guide for a Successful Step and Repeat Banner, Vail Fucci, event photographer (April 8, 2024): measuring, group size, logo size, file types, glare, wrinkles, lighting, stability